Changing Servers for a Website – Redirect Traffic to New IP for No Downtime While DNS Propagates

Wednesday, December 20th, 2023

Moving a Website to Another Server – Redirect Traffic to the New Server While DNS Propagates (for No Downtime)

If you're migrating a website from one server to another and have updated the DNS for the domain to point to the new server, some traffic will still be directed to the old server due to DNS caching.  So, while the DNS changes propagate over the internet (can take up to three days), you can still redirect traffic to the new server from the old server so that you won't suffer any downtime. 

On the old server, run these commands to redirect web traffic on port 80 (http) and port 443 (https) to the new server (adjust the {DESTINATION_IP_ADDRESS} variable accordingly):

echo 1 >/proc/sys/net/ipv4/ip_forward
iptables -t nat -A PREROUTING -p tcp --dport 80 -j DNAT --to-destination {DESTINATION_IP_ADDRESS}:80
iptables -t nat -A PREROUTING -p tcp --dport 443 -j DNAT --to-destination {DESTINATION_IP_ADDRESS}:443
iptables -t nat -A POSTROUTING -p tcp -d {DESTINATION_IP_ADDRESS} --dport 80 -j MASQUERADE
iptables -t nat -A POSTROUTING -p tcp -d {DESTINATION_IP_ADDRESS} --dport 443 -j MASQUERADE

Reference:  https://serverfault.com/questions/371833/changing-servers-redirect-to-new-ip-no-downtime#371870

Rebuilding a Removed / Failed RAID 10 Array in CentOS / Rocky Linux

Tuesday, February 22nd, 2022

Replace Hard Drive in a RAID 10 Array and Sync the RAID 10 Array to the New Hard Drive

I had the hardest time rebuilding a RAID 10 array after replacing a hard drive.  I didn't fail the old hard drive before removing it from the array, and sometimes, this may not be an option.  What happened in my case is the data center replaced the hard drive that I had shipped to them directly from an eBay seller.  I was hoping that the RAID array would rebuild itself onto the new drive (as I have seen happen before in some circumstances).  However, that may not happen if the replacement drive still has its old RAID array or partition information present, and then, it might be difficult to actually get the RAID array to sync to the new drive. 

In my case, I run LVM (Logical Volume Manager) for my partitions.  This complicates the RAID setup, and I found that mdadm commands didn't work as expected.  If this situation occurs, it is best to boot Rocky Linux or CentOS in recovery mode using a Rocky Linux ISO or CentOS ISO.  Once the recovery system loads, drop to a shell without mounting any file systems.  Next, you will need to deactivate your LVM volume group:

vgdisplay
vgchange -a n my_volume_group # deactivate

Next, examine your md RAID array by running the following command:

cat /proc/mdstat

After running that command, I identied my RAID devices as md126 and md127.  /dev/md127 is considered the parent even though /dev/md126 is where everything is. 

I can get more information about the RAID array by running the below commands:

mdadm --detail /dev/md126
mdadm --detail /dev/md127

Let's fail and remove any removed (no longer existing) drives using this command:

mdadm /dev/md126 --remove failed
mdadm /dev/md126 --remove detached
mdadm /dev/md127 --remove failed
mdadm /dev/md127 --remove detached

Next, we need to identify the hard drive we want to add / replace the removed drive in the array:

lsblk

From running the above command, I noticed that the new drive was /dev/sde, so I needed to wipe its old RAID configuration (if there is any) and then add it to the RAID array.

wipefs /dev/sde
mdadm --add /dev/md127 /dev/sde

Check to see if the syncing process has started:

cat /proc/mdstat

You may or may not need to run the below command to get the RAID device to start syncing to the new drive:

mdadm --grow /dev/md126 --raid-devices=4

Helpful Links:

https://delightlylinux.wordpress.com/2020/12/22/how-to-remove-a-drive-from-a-raid-array/
https://serverfault.com/questions/554553/how-to-delete-removed-devices-from-a-mdadm-raid1
https://unix.stackexchange.com/questions/53129/dev-md127-refuses-to-stop-no-open-files
https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/4/html/cluster_logical_volume_manager/vg_activate
https://serverfault.com/questions/676638/mdadm-drive-replacement-shows-up-as-spare-and-refuses-to-sync
https://serverfault.com/questions/554553/how-to-delete-removed-devices-from-a-mdadm-raid1

Recreating a Lost or Removed EFI Windows Boot Partition (Repair Windows Boot)

Wednesday, January 29th, 2020

Recreating a Lost or Removed EFI Windows Boot Partition

In case you remove an SSD with a Windows Boot Partition that boots an installation of Windows, you'll need to recreate the boot system to be able to successfully boot again.  To recreate the boot EFI partition on another drive or partition, perform the following:

1) Create or use an existing Windows installation disc or flash drive (you can use Rufus USB to format a flash drive with a Windows ISO)
2) Boot PC using your Windows installation media (a CD, DVD, flash drive, etc containing Windows installation files)
3) Press SHIFT + F10 on the first screen to bring up Command Prompt
4) Run the following commands and click Enter each time at Command Prompt:

diskpart
list disk
select disk N (N refers to the disk which contains the deleted the EFI System partition)
list partition
create partition efi size=200
format quick fs=fat32
list partition
list volume (find the volume letter which belongs to the installed Windows OS)
exit (exit diskpart)
bcdboot M:\windows (M refers to the volume letter of installed Windows OS)

Add any additional Windows installations by repeating the bcdboot command followed by the installation path for any other Windows installations you want added to the menu.  For example, I added my Windows 7 partition using the below command:

bcdboot P:\windows

You should now be able to boot Windows again without needing the old boot partition or drive.

Instructions were modified from this post.